Reinitialize your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may need to restore your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the configurations or are experiencing unexpected issues. Fortunately, resetting your Holosun is a straightforward process that can be performed in just a few procedures.

• First ensuring your red dot sight is activated.
• Identify the small reset button on the rear of the unit.
• Utilize a thin tool to press and hold the reset button for approximately 7 seconds.
• Disengage the lever and your Holosun EPS Carry Red Dot sight will reboot.
• Your red dot sight should now be set back to its factory settings.

Return to Your Holosun EPS Carry Red Dot to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to start fresh, resetting it back to standard configuration is a breeze. First, find the tiny button on the side of your optic. Then, press and hold it for around twelve seconds until you see a brief flash. Your Holosun EPS Carry is now reset to its factory settings, ready for consistent targeting.

restore Your Holosun EPS Carry Back to Action

Is your beloved Holosun EPS Carry experiencing some issues? Don't despair! A simple factory reset can often fix the problem get more info and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these straightforward steps:

• Hold down the power button for approximately 7 seconds.
• A message will flash, indicating that the reset is in progress.
• Let go of the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and verify your sight's functionality. If you encounter any further problems, don't hesitate to contactsupport team.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Follow these steps carefully to ensure a successful factory reset.

• First, Energize your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• During continue holding these buttons, press the power button once.
• You will show a confirmation prompt indicating that the reset process is initiated.
• Allow the process to conclude. This may take a few moments. Once done, your Holosun EPS Carry will automatically deactivate.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Clear All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Pressing a specific button combination. Consult your Guidebook for the exact button sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Reset your Holosun EPS Carry through a Factory Standard Settings

If your Holosun EPS Carry is acting up, a factory reset might be the fix. This will set back your sight to its initial settings, clearing any custom configurations you've made. To accomplish this reset, follow these straightforward steps:

• Initially, find the reset button on your EPS Carry.
• Then, use a small object, like a pen tip, to activate the reset lever.
• During hold the reset lever activated, power on your EPS Carry.
• You'll display a message confirming that the reset is finished.

When the reset is finished, your EPS Carry will be returned to its factory settings.

Report this wiki page